Viessmann VITOCAL 300-G Operations Instructions Page 207
- Page / 256
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
207
Service menu:
1. Press OK + å simultaneously for
approx. 4 s.
2. "Coding level 1"
3. "Heating circuit 1"
or
"Heating circuit 2"
or
"Heating circuit 3"
or
"Separate cooling circuit"
4. Select parameter.
Note
The parameters in the parameter groups
Heating circuit 1, Heating circuit 2 and
Heating circuit 3 are identical.
The assignment to the heating circuit is
determined by the first digit of the param-
eter code:
2xxx for heating circuit 1
3xxx for heating circuit 2
4xxx for heating circuit 3
2000/2001/2022 Room temperatures and switching times
"Standard room temperature 2000"
"Reduced room temperature 2001"
"Party temperature 2022"
Adjusting the set room temperatures and
time programmes for all heating circuits
(A1, M2 and M3).
Operating instructions
"Standard room tempera-
ture 2000"
"Party temperature 2022"
"Reduced room tempera-
ture 2001"
Delivered condition
200 (≙ 20 °C) 160 (≙ 16 °C)
Setting range 100 to 300
(
≙
10 to 30 °C)
100 to 300
(
≙
10 to 30 °C)
2003 Enabling the remote control
"Remote control 2003"
Parameter group heating circuits/cooling circuit
Parameter group heating circuits
5442 829 GB
Service
- VIESMANN 1
- Safety instructions 2
- Installation instructions 4
- Service instructions 4
- Product information 9
- Installation 10
- Heating circuit 17
- Cooling operation 19
- DHW heating 20
- External heat source 21
- Power-OFF 22
- Electrical connection 23
- I>I>I> 26
- With two primary pumps 27
- With a common primary pump 28
- Preparing for installation 30
- (cont.) 30
- 230 V / 50 Hz 33
- Low voltage 39
- 230 V/50 Hz 39
- Two-stage heat pump cascade 41
- System example 1 44
- System example 2 52
- 230 V/50 HzLow voltage 66
- Levelling the heat pump 67
- Installing the heat pump 67
- Remove top panel 69
- < 42 V 70
- Hydraulic connections 71
- Installation sequence 74
- Overview of connections 75
- Connecting sensors 83
- Connecting pumps 85
- Other components 90
- Cooling functions 92
- Swimming pool water heating 99
- Cascade control via KM BUS 100
- Electrical connections 100
- Power supply 103
- Connecting power cables 105
- Power supply with power-OFF 108
- Phase monitor 113
- Closing the heat pump 115
- Checking grommets 116
- 5442 829 GB 118
- Opening the heat pump 119
- Writing reports 119
- Commissioning assistant 121
- Instructing the system user 125
- Scanning messages 126
- Messages 126
- Message overview 127
- Diagnosis (service scans) 150
- Calling up diagnosis 150
- Scanning operating data 150
- System overview 151
- Heat pump module diagnosis 154
- Select with 160
- Energy statement htgÜ 160
- Wk. 23/09 160
- Brief scan 161
- Function check 163
- Checking sensors 166
- Checking the fuse 167
- Appliance too noisy 167
- Removing the heat pump module 168
- Activating service menu 171
- Disabling the service menu 171
- 7000 System scheme 173
- 7001 Language 173
- 7010 External extension 175
- 700A Cascade 176
- 5735 Number of lag heat pumps 176
- 7008 Swimming pool 176
- 700B Output of lag heat pumps 177
- 7017 Vitocom 100 184
- 5000 Enable compressor 185
- 5030 Heat pump output 185
- Parameter group compressor 185
- 5130 Heat pump output 186
- Parameter group compressor 2 186
- 6000 Set cylinder temperature 189
- 6015 DHW reheating 189
- Parameter group DHW 189
- 6009 DHW start optimisation 191
- 600A DHW stop optimisation 192
- 600C Set DHW temperature 2 192
- 600E Temperature sensor 2 192
- 6016 DHW heating priority 192
- 7A00 Solar control unit 195
- Parameter group solar 195
- 790A Stage at power-OFF 197
- 7303 Screed program 199
- 7203 Hysteresis 204
- 7204 Maximum temperature 205
- 7100 Cooling mode 211
- Parameter group cooling 211
- 7101 Cooling circuit 212
- Parameter group time 214
- 7710 LON communication module 215
- Parameter group communication 215
- 7779 Fault manager 216
- 77FF Time via LON 217
- 8800 Lock out controls 219
- Parameter group operation 219
- Controller and sensor PCB 228
- Parts list 231
- Control parameters report 236
- Hydraulic parameters report 236
- Specification 241
- Heat pump commissioning order 246
- Declaration of conformity 247
- Keyword index 248
- Applicability 256
Related products and manuals for Water pumps Viessmann VITOCAL 300-G
(206 pages)© 2020, manymanuals.com. All rights reserved. | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals