Viessmann VITOTRONIC 100 GC1B Installation Manual Page 143
- Page / 164
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
143
5793 309 - 04
Vitotronic 100, GC1B / Vitotronic 300-K, MW1B Installation and Service
“DHW” Group (continued)
Coding 2, Vitotronic 300-K
Coding in the factory set condition Possible change
62:10 DHW pump with a run-on time after DHW tank
heating of max. 10 min.
62:0 DHW pump without run-on.
62:1
to
62:15
Run-on time adjustable from 1 to 15 min.
64:2 During party mode and after external changeover
to constant operation with the standard room
temperature:
Constant DHW heating enabled and DHW
recirculation pump “ON”.
64:0 No DHW heating, DHW recirculation pump
“OFF”.
64:1 DHW heating and DHW recirculation pump
according to time program.
66:4 Input of the set DHW temperature:
At the control unit programming unit and all
installed Vitotrol 300A remote controls.
66:0 At the control unit programming unit.
66:1 At the control unit programming unit and remote
control system circuit A1 (heating circuit ).
66:2 At the control unit programming unit and
remote control heating circuit with mixing valve
M2 (heating circuit 2).
66:3 At the control unit programming unit and
remote control heating circuit with mixing valve
M3 (heating circuit 3).
66:5 At the remote control system circuit A1
(heating circuit 1).
66:6 At the remote control heating circuit with
mixing valve M2 (heating circuit 2).
66:7 At the remote control heating circuit with
mixing valve M3 (heating circuit 3).
67:40 For solar DHW heating:
Set DHW temperature 104°F (40°C). Reheating
is suppressed above the selected set temperature
(DHW heating by the boiler only if solar energy is
not sufficient).
67:0 No third set value.
67:10
to
67:95
Set DHW temperature adjustable from 50 to
194°F (10 to 95°C). (limited by boiler specific
parameters).
Observe the setting of coding address “56”.
68:8 With 2 DHW tank temperature sensors
(code “55:2”):
DHW tank heating stop point at set value x 0.8.
68:2
to
68:10
Factor adjustable from 0.2 to 1;
1 step
0.1
69:7 With 2 DHW tank temperature sensors
(code “55:2”):
DHW tank heating start point at set value x 0.7.
69:1
to
69:9
Factor adjustable from 0.1 to 0.9;
1 step
0.1
6A:75 Runtime, actuator, mixing valve, heat exchanger
set, Vitotrans 222, (80 and 120 kW):
75 sec.
6A:10
to
6A:255
For heat exchanger set Vitotrans 222 (240 kW):
set 113 sec.
Runtime adjustable from 10 to 255 sec.
70:0 DHW recirculation pump “ON” according to time
program when DHW heating is enabled.
70:1 DHW recirculation pump “ON” according to
time program.
71:0 DHW recirculation pump:
“ON” according to time program.
71:1 “OFF” during DHW heating to the first set value.
71:2 “ON” during DHW heating to the first set value.
72:0 DHW recirculation pump:
“ON” according to time program.
72:1 “OFF” during DHW heating to the second set
value.
72:2 “ON” during DHW heating to the second set
value.
73:0 DHW recirculation pump:
“ON” according to time program.
73:1
to
73:6
“ON” from once per hour for 5 min. up to
6 times per hour for 5 min. during the time
program.
73:7 Constantly “ON”.
75:0 DHW recirculation pump “ON” during economy
mode according to time program.
75:1 DHW recirculation pump “OFF” during economy
mode.
- IMPORTANT 1
- Product Information 2
- For your Safety 6
- About these Instructions 7
- Overview of System Examples 8
- System Example 1 9
- System Example 1 (continued) 10
- System Example 2 17
- System Example 2 (continued) 18
- System Example 3 (continued) 25
- System Example 4 (continued) 33
- System Example 5 41
- System Example 5 (continued) 42
- Mounting the Control Unit 49
- Control Unit Installation 50
- Opening the Control Unit 51
- Vitotronic 100, Installation 52
- Pump Connection Overview 54
- (if required) 56
- Connecting Sensors 57
- Power Supply 58
- External Connections 59
- Connecting Actuators 60
- Connections to Terminal aBA 62
- External Burner Blocking 62
- Connecting Pumps 75
- Connecting Actuators 79
- Making the LON Connection 83
- Commissioning 84
- Adjusting Heating Curves 92
- Calling up Service Level 94
- Exiting the Service Level 94
- Scanning Operating Data 94
- Brief Scan 95
- Service Scans, Vitotronic 100 96
- Calling up the Service Menu 97
- Fault Display 99
- Fault Codes 100
- Fault Codes (continued) 101
- Fault Display 103
- Function Description 108
- Calling up Coding Level 1 119
- Group 1 “General” 120
- Group 2 “Boiler” 120
- Group 2 “Boiler” (continued) 121
- Calling up Coding Level 2 122
- Group 1 “General” (continued) 124
- “General” Group 129
- “Cascade” Group 130
- “DHW” Group 130
- “Solar” Group 131
- Coding 1, Vitotronic 300-K 132
- “General” Group (continued) 137
- “Cascade” Group (continued) 142
- “DHW” Group (continued) 143
- “Solar” Group (continued) 145
- Coding 2, Vitotronic 300-K 147
- Connection and Wiring Diagram 151
- Wiring, Vitotronic 100 152
- Wiring, Vitotronic 300-K 155
- Components 158
- Mixing Valve Motor Kit 159
- Parts List Vitotronic 100 161
- Parts List Vitotronic 300-K 162
- Specification Vitotronic 100 163
- 5793 309 - 04 164
Related products and manuals for Water heaters & boilers Viessmann VITOTRONIC 100 GC1B
(52 pages)© 2020, manymanuals.com. All rights reserved. | 2.780 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals